What sizes does Peter Lewis Paints Lime Render come in?
20 kilograms and 1 kilogram sample pots.
What is the coverage of Peter Lewis Paints Lime Render?
Coverage will vary depending on the texture of the substrate. A 20kg pail will cover approx. 12-20 m² at 1mm thick. This does not include any allowance for wastage.
All coverage recommendations should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the coverage of our products.
What is the drying time for Peter Lewis Paints Lime Render?
Peter Lewis Paint’s Natural Lime Render can be reworked after 8 hours, however further coats should not be applied for 2 to 7 days, once the primary coat has stiffened/hardened, but is still ‘green’.
All drying recommendations should only be used as a guide, as it is truly dependent on thickness of application, the substrate below and weather conditions. Please contact us for more information regarding the drying time of our products.
What surfaces can I apply Peter Lewis Paints natural Lime Render to?
Peter Lewis Paints Lime Render can be applied onto brick, stone or concrete, (including tilt-up panels) with one or two base coats and a finish coat.
If applying to any other surface, please contact us before use.
What preparation is needed for the surface before applying Lime Render?
Remove dust, surface contaminants and loose or friable existing render/plaster. Where necessary, consolidate or dub out any deep holes with Peter Lewis Paints Lime Render and key. Ensure masonry is not waterproofed or painted. Dampen the surface with a mist spray in sufficient quantity to reduce excessive suction.
For any other queries about Lime Render preparation, please contact us.
What is the best weather to apply Lime Render?
To apply Peter Lewis Paints eco-friendly Lime Render, surface temperature, at all times, above 5ºC and below 30ºC. Do not apply when the weather is expected to be hot for a number of days.
For any other queries about Lime Render application please contact us.
How many coats of Peter Lewis Paints Lime Render do I need?
Apply 2-3 coats of 1-2 mm each on straight walls in unexposed or exposed locations. Please allow 2 to 7 days before the secondary coats are applied, once the primary coat has stiffened/hardened, but is still ‘green’. Please read the FAQ labelled ‘How do I apply Peter Lewis Paints Lime Render?’ for exact application instructions.
However, this recommendation should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the application and coverage of our products.
How do I apply Peter Lewis Paints Lime Render?
Apply 2-3 coats of 1-2 mm each on straight walls in unexposed or exposed locations. Each coat must be scratched to give a good mechanical key before further coats are applied. Dampen down the surface prior to coating. A second Lime Render coat may be applied after the previous has adequately cured, usually 2-4 days. Ensure it is thinner than the first. Key the final coat of Lime Render whilst still green with a nail or devil float before applying the topcoat of Lime Render. The final coat should be treated the same as previous coats. The final top coat of Peter Lewis Paints Lime Render needs no final finishing but an application of Peter Lewis Paints Mineral Silicate Paint can be applied over top if desired.
Prevent all coats from drying out too rapidly. Lightly spray each coat with water if it is hot or the product is drying out too quickly. Protect from adverse conditions such as frost, rain, etc. Adequate curing of a final decorative coat should be more stringent, ideally using a fully sheeted scaffold when outside. Do not allow it to dry quickly to avoid cracking and crumbling of the render.
For any other queries about Lime Render application please contact us.
Are there any safety cautions with Peter Lewis Paints Lime Render?
Due to the Lime based nature of Peter Lewis Paints natural Lime Render, if contact with the eyes occurs, rinse with running water and seek help if irritation persists. Avoid long periods of skin contact. If swallowed do not induce vomiting. Give a glass of water and seek medical assistance or contact the Poison Information Centre (13 11 26).
Please refer to the Safety Data Sheet for more safety information.
Can I apply Peter Lewis Paints Lime Render over existing paint?
Yes, Peter Lewis Paints eco-friendly Lime Render can be applied over existing paint, however, where painted surfaces are loose, peeling or flaking, these surfaces must be made sound first, by removing loose paint, filling any cracks and nail holes with a suitable filler. Then it should be prepared and dusted off. All repaired areas to be spot primed with our Rocky Stone Paint Fine, then apply one coat to the entire area. It should be touch dry in 2 hours, however, allow 6 hours dry time. After this process, the surface is ready for Lime Render application.
For any other queries about Lime Fresco application please contact us.
What Trowel should I use to apply Peter Lewis Paints Lime Render?
The best trowel for Lime Render Application is our CO.ME Trapezoidal Render Trowel.
Can you recommend any applicators to apply Peter Lewis Paints Lime Render?
Yes, we have applicators around NSW that are experienced using our product that we recommend to our clients. Please contact us to find out more.
