What sizes does Peter Lewis Paints Natural Emulsion Dead Flat come in?
1L, 4L and 15L.
What is the coverage of Peter Lewis Paints Natural Emulsion Dead Flat?
Peter Lewis Paints Natural Emulsion Dead Flat Paint will cover approximately 14m2 per litre, yet is truly dependent on the porosity of the substrate.
All coverage recommendations should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the coverage of our products.
What is the drying time for Peter Lewis Paints Natural Emulsion Dead Flat?
Peter Lewis Paints sustainable Dead Flat Paint will be touch dry in 2 hours, in dry, well ventilated areas. Allow adequate cross ventilation during and after use to dissipate water vapour. Please allow 6 hours of drying time between coats. Allow new paint to cure for at least seven days.
All drying recommendations should only be used as a guide, as it is truly dependent on thickness of application, the substrate below and weather conditions. Please contact us for more information regarding the drying time of our products.
What surfaces can I apply Peter Lewis Paints Natural Emulsion Dead Flat to?
Peter Lewis Paints Natural Emulsion Dead Flat Paint is for use on suitably prepared surfaces such as plasterboard, cement render, brick and masonry. It is not recommended for roofs collecting potable water or as a finish for contact surfaces such as windows and doors etc. Instead our Natural Emulsion Satin Trim product is recommended for these applications.
If applying to any other surface, please contact us before use.
What preparation is needed for the surface before applying Natural Emulsion Dead Flat?
Remove mould, grease, chalking and flaking paint; dust off all loose matter. Allow new cement render to cure for 30 days, rub down with a carborundum stone to remove loose sand and sweep down before applying any coating. New fibrous plaster and previously chalky surfaces must be sealed with our Professional Surface Binder. Rust prone metals such as screw and nail heads are to be rendered rust resistant. Dried brown water stains generally found on ceilings must be sealed with a suitable stain blocking sealer. Prime/undercoat all unpainted interior timber with Peter Lewis Paints Universal Primer. Glossy surfaces are to be sanded and dusted down first. Interior chipboard/MDF should be considered as timber. Fill all cracks, nail holes etc. with a suitable filler.
What is the best weather to apply Natural Emulsion Dead Flat?
Peter Lewis Paints eco-friendly Dead Flat Paint should not be applied in high humidity, or when the surface temperature is below 10°C or above 30°C.
For any other queries about the application of our products please contact us.
How many coats of Peter Lewis Paints Natural Emulsion Dead Flat do I need?
Two coats of Peter Lewis Paints Natural Emulsion Dead Flat Paint are typically required, however more coats may be required for deeper colours and when applying on more porous surfaces. Please allow 6 hours of drying time between coats.
This recommendation should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the application and coverage of our products.
How do I apply Peter Lewis Paints Natural Emulsion Dead Flat?
Check colour before application.
For previously unpainted surfaces: Apply one coat of Peter Lewis Paints Universal Primer. Allow to dry for 6 hours before applying two coats of Peter Lewis Paints Natural Emulsion Ultra Low VOC Dead Flat, allowing 6 hours between coats.
Previously painted surfaces: Ensure surface is sound and free of any contaminants. Apply two coats of Peter Lewis Paints Natural Emulsion Ultra Low VOC Dead Flat. Allow 6 hours between coats
Peter Lewis Paints Natural Emulsion Dead Flat Paint should not be applied in high humidity, or when the surface temperature is below 10°C or above 30°C.
For any other queries about the application of our products please contact us.
Are there any safety cautions with Peter Lewis Paints Natural Emulsion Dead Flat?
Keep out of reach of children. Paint containers must be properly sealed at all times when not in use. If contact with the eyes occurs, rinse with running water and seek help if irritation persists. Avoid long periods of skin contact. If swallowed, do not induce vomiting. Give a glass of water and seek medical assistance or contact the Poison Information Centre (13 11 26).
Please refer to the Safety Data Sheet for more safety information.
Can I apply Peter Lewis Paints Natural Emulsion Dead Flat over existing paint?
Peter Lewis Paints eco-friendly Dead Flat Paint can be applied over existing paint, but please ensure the surface is sound and free of any contaminant before applying two coats of Peter Lewis Paints Natural Emulsion Dead Flat. Allow 6 hours between coats. However, if painting with a lighter shade over a dark colour, please apply two coats of Peter Lewis Paints Universal Primer before applying the dead flat paint.
For any other queries about Peter Lewis Paints Natural Emulsion Dead Flat application please contact us.
Can you recommend any applicators to apply Peter Lewis Paints Natural Emulsion Dead Flat?
Yes, we have applicators around NSW that are experienced using our product that we recommend to our clients. Please contact us to find out more.